FR-A024 MANUAL PDF
Background: When released, the FR-A/A offered unmatched functionality and reliability Please confirm all specifications with the applicable manuals. Thank you for choosing the Mitsubishi Inverter. This instruction manual gives handling informalion and precautions for use of this equipment. fr-ak manual Related manual: sgdhae manual, lenze highline manual, elau mc 4 manual, Mitsubishi FREQROL-A / A Manual (pdf).
|Published (Last):||8 March 2008|
|PDF File Size:||15.39 Mb|
|ePub File Size:||10.79 Mb|
|Price:||Free* [*Free Regsitration Required]|
Mitsubishi FREQROL-A024 / A044 General Purpose Inverter
Two SD terminals are internally connected. Manual Freqrol A Mitsubishi – Ima searching for a book Manual freqrol a mitsubishi in pdf form, then you have come on to the right website. In the external or combined operation mode, it is not possible to write the set value.
Followthestepsindicated below to remove it from the inverter. AY40A Use external power supply with a higher supply voltage than the inverter power supply.
In a remote installation, the parameter unit may be used as a hand-held unit or mounted in an enclosure. This instruction manual gives handling informalion and Documents. Combination operation mode Operation by combining the external signals and parameter unit keys. Use the start slgnal at the inverter.
Switch off the start signal when resetting the inverter. The serial number is shown on the name plate. InverterU JIttakesmorethan 60 sec for discharge of the internal capacitor after disconnecting power supply.
III 2 Pull the parameter unit cover to the left to remove it from the parameter unit. Fr-024 or degradetheperformanceofthe inverter.
I f power is OH, do not remove the front cover except for wiring or periodic inspection. The procedure to set the default mode for the mode which is established when power is turned on is explained on page Refer to page 57 lor a complete list of For details of the setting procedure, refer to page parameters.
Failure to do so may start the motor immediateiy after reset. However, even in the external or conbination operation mode, writing is possible for the following parameters. Alter attaching ttte fmnt c a wtsst to make sure that k is securety held in phca by the latches.
The electronic motor thermal protection does not guarantee lo prevent motor burn out. The inverter can be easiiy set for high-speed operatin. Mitsubishi Freqrol A Inverter a Mitsubishi freqrol a inverter manual, Do not run the inverter Ath the front cover removed.
Prepare an emergency stop switch separately. Wire sue Rder to “Selection of Peripheral Devices” page Assumes that incorrect handling may cause hazardous conditions, resulting in death or severe injury.
Do not use the optional brakeunit and brake resistor simultaneously. Published on Nov View Download 5. The connection orientalion of the output cables U, V, W to the motor will affect the direction of rotation of the motor.
Do not connect or frr-a024 these terminals. Screw size M3 screws 2. Otherwise, you may access the exposed high-voltage terminals and charging parl and get an electric shock. Always replace the cover and follow this instruction manual when operating the inverter.
Points where ambient temperature is measuredPlaces subject to vibration. Mitsubishi Freqrol A Inverter Manual – freqrol a user’s guide service manual mitsubishi freqrol a Two terminals beneath the terminal block Screwsize.
After parameter copy from old version fr-a24 new version, manually set 0 to Pr. Places exposed losideways InstallationKeep m b k n t tempr. I0I Attaching the front coverInsert the tabs 2 pcs.
fr-ak manual(PDF) –
Remember that reading is possiMe in any of these operation modes. Ambient temperature should be held Whin the specified l m i k fg-a024 heat dissipation.
Failure to do so could cause the brake resistor to abnormally overheat and a fire to start if a fault occurs in the brake transistor, etc. Installation L d o n The service Iile of me inverter is influenced by temperature.
Use the guide pin and guide slot to determine the correct connector orientation.
A continuous flow of a large current could cause a fire. Re-set the requlred parameters before starting operation. MeasuresInsert a diode to prevent undesirable c u m t.
WIRING-Items to fr-x024 Checked when Designing an Application 1 If the application has acommercial power supply selector circuit as shown in the illustration to the right, accidental connection of line I M inverter output terminals will Power power to I damage the inverter.